Cozy Cotton Terry Cover Up Pattern
It's almost pool time (or beach time if you're lucky)! Time for a cute cover-up for baby. This is made from a towel, 1/2 yard of cute cotton, some double-fold bias tape and a few snaps. It's all cozy on the inside and cutesy on the outside. I totally dig it and want a giant one to wear around the house all day while I write, ha, can you imagine?
I am so beyond in love with Alexander Henry Bird Seed Fabric (also made the DIY Changing Pad Cover out of it) which is sold out pretty much everywhere but you can find some in aqua and yellow at Fabricworm! Get the full Terry Toddler Cover Up Pattern after the jump...
Terry Toddler Cover Up
1. Gather your materials: One bath towel (or you can buy some terry but a towel actually will be easier for the project), 1/2 yard of cotton, 2 packages of double-fold bias tape (about 4 yards), a box of snaps(plastic or metal) and a 10" piece of 1/2" elastic (the width isn't super important so whatever you have on hand).
2. Let's cut all our pieces. Cut the sides off the towel like so:
Take one of those sides and cut it in half:
From that half cut two 1.5" thick strips:
Now take the towel and cut it down to 36.5" wide and discard the little remaining bit of towel:
At the very top of your 36.5" piece, cut a strip 1.5" wide and save the strip, we'll be using it later (you want that finished edge on it):
Now cut the length of the towel down to 18.5". So the body of your towel is now 36.5" wide and 18.5" long. Cut your 1/2 yard of cotton to the same size.
3. Now let's make our straps. So take one of your small strips and your bias tape, check which side of the tape is slightly wider:
Open the bias tape and pin the wide side aligned with one edge of your strip. At one edge fold the bias tape over the strip and pin so it's attached on both sides like so:
Sew it in place along the fold:
Fold the bias tape back up and wrap it around to the other side of the strip and pin:
And sew it in place right at the edge. Because you are stitching on the shorter side of the bias tape your stitches will catch on both sides.
Repeat the process on the other side of that strip, and on both sides of the other strip to create your straps:
Take the edge of each strip with the folded over bias tape, fold the whole end under 1/4" and sew in place:
Now get out your snap kit. If you've never used one you should, it's so easy, you just use the little tool and hammer the snap in place according to the directions. Here's a kit to check out. One billion times easier then sewing buttonholes or sewing snaps on yourself, though you can if you really want to. On the finished end of each strap, measure in 1" and 2" from the end (so the snaps are 1" apart) and attach a snap backing. This will allow your towel to grow with your toddler:
Set the straps aside.
4. Now grab the 36.5" long strip we cut earlier (with the finished edge- if you're using straight terry, go ahead and finish one edge of it). With the unfinished edge facing up measure 1" and 4" in from the left side (so the snaps are 3" apart) and attach two snap fronts:
Also measure 14" in from each side and attach two snap fronts. So now your strip has 4 snap fronts on it:
Set that aside.
5. Now for the body of the towel. Pin your towel and your cotton together wrong sides facing (so you see the pattern):
Sew in place all the way around the edge with 1/4" inseam. It doesn't matter what color thread because you won't see this later:
Now lay your towel flat with the cotton facing you. On the top left corner measure in 1" and 4" (so the snaps are 3" apart) and attach two snap backings:
Now lay your towel terry side up, open up your bias tape, and pin the wider side all the way around with the edge of the bias tape aligned with the edge of the towel Curve it at the bottom corners for extra cuteness like so:
Sew in place along the fold, the cut the excess fabric from your rounded corners:
Turn the towel over, fold the bias tape back up, enclosing the unfinished edge, pin and top stitch in place:
6. Now measure in 6.5" from each edge and pin the unfinished edge of your straps towards the inside with the snaps facing down:
it should look like this (you see the folded edge of your strap is up):
See there they are pinned to both sides:
Now take the crazy strip we made earlier and pin it right side down (so you can't see your snap fronts) to the front of the towel over the straps:
Sew that in place along each short side edge (at the very edge) and across the top with 1/4" in seam. It might help to turn it over and follow the thread line you made earlier when sewing your terry and cotton together, just to be sure you are sewing right inside that line:
Now flip the strip over to the back of the towel and iron it flat. Now your straps are in place.
This is a little tricky so pay attention. Measure in 9" from the left side and pin your piece of elastic in place under the strip. Do the same on the right side. Your towel will gape in the middle like so:
Sew each end of the elastic in place with a straight stitch, perpendicular to the strip:
Fold the strip over the elastic and pin it in place (don't pin the elastic):
Sew the edge of the strip down (don't sew your elastic). You may want to use a thread that matches your towel on the spool and one that matches your cotton in the bobbin so it all coordinates:
LADY YOU DID IT! It wasn't that bad right? Snap your straps into place in the back, and your two snaps in the front. It feels so luxurious doesn't it?
So here it is all opened up.
And from the back:
Is this too many pictures? Can you tell i'm proud?
and there's my baby all snuggled up in it after bathtime: